CONTROL PANEL r FREQENCY indication Indicates or inputs the receive frequency.w COM port button Used to select a COM port. POWER PANEL q POWER button Turns IC-PCR100 on and off.Most of the adjustments in this section must use EX-2206, an adjust- ment program for IC-PCR100. Outputs band.ĥ-1 PREPARATION BEFORE SERVICING The receiver (IC-PCR100) can be adjusted by sending adjustment data to the RS-232C port via a PC. High: When frequencies from 1.8 to 14.999 MHz are displayed. High: When frequencies below 1.8 MHz are displayed. Outputs power switch.Ĥ-4-2 OUTPUT EXPANDER IC (1) IC1 (2) IC3 4 - 7 Outputs low-pass filter select signal. Input ports for the CPU system clock oscillator (X6 9.8304 MHz). Ĥ-4 PORT ALLOCATIONS 4-4-1 CPU (IC20) CPU (IC20) - continued 4 - 6 Input port from WFM IC (IC7, pin 7) for the stereo indicator. The generated signal at the VCO 3 (Q34) enters the PLL IC (IC8, pin 13) via the buffer amplifier (Q35), is divided ath. Ĥ - 5 4-2-3 2ND LO LOOP The 2nd LO circuit generates the 2nd LO frequencies, and the signals are applied to the 2nd mixer circuit. The CPU compares these signals, then outputs a control signal. S-METER SQUELCH The S-meter signal is applied to the CPU from the meter amplifier circuit (IC13a) via the SMAD line, and also the S- meter squelch setting level is applied to the CPU.The 10.7 MHz 2nd IF signal from the IF amplifier (Q29) is applied to the 3rd mixer section in the F. The.Ĥ - 2 The 150–349.999 MHz signals from the band switching diode (D16) pass through the high-pass filter (L27–L29, C69–C74) and tunable bandpass filter (D18, 元1–元3), and are then amplified at the RF amplifier (Q9) and pass through another tu.Ĥ - 3 4-1-7 3RD MIXER CIRCUIT The 3rd mixer circuit mixes the 2nd IF signal and 3rd LO sig- nal to produce a 450 kHz 3rd IF signal (except WFM mode). 20 dB to protect the RF amplifier from distortion when excessively strong signals are received. SECTION 4 CIRCUIT DESCRIPTION 4 - 1 4-1 RECEIVER CIRCUITS 4-1-1 RF ATTENUATOR CIRCUIT The attenuator circuit attenuates the signal strength to approx. Removing the antenna plug and shield U-plate 1 Unscrew the.3 Remove the cover panel in the direction of the arrow. Removing the cover panel 1 Unscrew 4 screws, A.Frequency resolution : 1 kHz (minimum) Ģ - 1 SECTION 2 INSIDE VIEWS ¡MAIN UNIT Bottom view Top view 0.01–1.8 MHz RF filter circuit 1.8–15 MHz RF filter circuit 15–30 MHz RF filter circuit VCO3 circuit Reference oscillator (X5: CR-629 12.8 MHz) VCO1, VCO2 circuits AGC control circ.ģ - 1 SECTION 3 DISASSEMBLY INSTRUCTIONS.Frequency range : *Specifications guaranteed 0.5–1300 MHz only.TABLE OF CONTENTS SECTION 1 SPECIFICATIONS SECTION 2 INSIDE VIEWS SECTION 3 DISASSEMBLY INSTRUCTIONS SECTION 4 CIRCUIT DESCRIPTION 4 - 1 RECEIVER CIRCUITS. DO NOT force any of the variable components. DO NOT open the receiver until the receiver is discon- nected from its power source. Make sure a problem is internal before disassembling the receiver.
#ICOM IC PCR100 MANUAL#
If you prefer to be anonymous write it in the message.SERVICE MANUAL COMMUNICATION RECEIVER FOR COMPUTER iC-pcr100
By click on the link you start a new message thread that only is related to ADI AR-247, and not to any of the articles.Ĭlick here to write a new message or comment for IC-PCR1000 Note that the message is not related to any article.Ĭlick here to see the article list for IC-PCR1000.ĭo you have any tricks, modifications or constructions for homebrewed equipment that are not on mods.dk, please send the information to mods.dk. If you like to write a new message you can do it by click here. There are no messages for this model at the moment.
If the message is relate to an article, the article can be selected next to each message.
This forum message list include all message for that is related to IC-PCR1000, this include message that also is related to articles. Note that page can take a while to load, if there are many modifications.
0 kommentar(er)
